Literature

ALLEN BRADLEY 1305 VFD MANUAL PDF

However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Zura Malak
Country: Iceland
Language: English (Spanish)
Genre: Business
Published (Last): 6 October 2012
Pages: 25
PDF File Size: 13.65 Mb
ePub File Size: 16.49 Mb
ISBN: 509-8-79143-276-7
Downloads: 17915
Price: Free* [*Free Regsitration Required]
Uploader: Dulmaran

An active local bus adapter is disconnected while it possesses control of a local bus function. Hz Err Fault – F29 No valid operating frequency.

Error 2 – The number of parameters in saved profile does not equal master number. Error 5 – Drive is running while attempting download.

Overload Fault – F7 Internal electronic overload trip. A longer acceleration tiime or a lighter load may be required. Check for broken wires, loose connections, or transducer loss at mA input, TB2. Check for external noise sources. DC Bus voltage fell below the minimum value. Overtemperature Fault – F8 Temperature sensor detects excessive heat.

The last parameter programmed will be displayed on the top line. DC Braking cannot be used with a synchronous motor. Check the external potentiometer circuit at TB2, terminals 1, 2, and 3 for a disconnected current. No valid operating frequency. Phase W Fault – F40 A phase to ground fault has been detected between the drive and motor in this phase.

  DIVINE WILL AND PREDESTINATION ASHQAR PDF

Check the motor for grounded phase. Mqnual frequencies and skip bandwith eliminate all operating frequencies.

Allen Bradley Adjustable Frequency AC Drive AB

Check programming of [Curr Lim Trip En] parameter. Reprogram Fault – F48 May occur when drive parametersare reset to default settings. Verify that the parameter has been programmed correctly. Check for a short circuit at the drive output or excessive load conditions at the motor.

Allen Bradley 1305 Adjustable Frequency AC Drive User Manual

Fast repairs at low costs. Stop drive, then re-run download. Inspect for breaks in communications line. Reset to Default Parameters and Cycle power.

1305 AC Drives

Phase V Fault – F39 A phase to ground fault has been detected between the drive and motor in this phase. Extend the deceleration time or instal dynamic brake option.

Check the Manuap line for high line voltage or transient conditions. Drive Reset Fault – F22 May occur on power-up. Open Pot Fault – F9 An external vcd is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard. Error 5 – Drive is running while attempting download Repeat operation. May occur on power-up. Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current.

Unplug the HIM from the cable fvd drive, then reconnect it. Inspect for short at the drive output or excessive load conditions on the motor, especially cable capacitance to ground. Reset your drive to the factory default settings.

  8251A USART PDF

Save a new profile. Check for proper mounting and spacing. Inspect the wiring between the drive and motor. Verify that all parameters have been programmed.

Phase U Fault – F38 A phase to ground default has been detected between the drive and motor in this phase. Error 3 – Download was attempted to a different type allne i. Serial Fault – F10 An active local bus adapter is disconnected while it possesses control of a local bus function.

Change [Cable Length] to “Long” if applicable. Bus overvoltage can also be caused 13305 motor reeneration. Power Test Fault – F46 Fault detected during initial start-up sequence. Check motor for grounded phase. An external pot is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard.

The Adjustable Frequency AC drive is available with ratings 0. Capabilities of drive are different than the master drive. Inspect to ensure that the kanual temperature limit has not been exceeded. Inspect fault buffer for fault code requiring reset.